KX mL ( US gt). KX | mL ( US gt). Depending on the atmospheric temperature of your riding area, the transmission oil viscosity should . Kawasaki. KX KX Motorcycle Service Manual This quick reference guide will assist you in locating a desired topic or procedure. • Bend the pages back. KX specs Completely redesigned for , the KX has received a number of . Kawasaki Kx Service Manual Repair Kx

Author: Kelrajas Zulutaxe
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Politics
Published (Last): 22 November 2004
Pages: 361
PDF File Size: 7.97 Mb
ePub File Size: 17.6 Mb
ISBN: 421-6-21597-456-2
Downloads: 18641
Price: Free* [*Free Regsitration Required]
Uploader: Zulkikazahn

Torque – Caliper Mounting Bolts: D DMA2 — — — Length: UPC Does not apply. Clutch Cable Lubrication and Inspection Great only place i could fine this manual in paper form p d 1 Air, however, is easily compressed.

Kawasaki KX (KXM2) OEM Parts, Babbitts Kawasaki Partshouse

Learn and ob- serve all the rules below. All pages bright, clear, and legible. Tighten all snugly, then loosen, retighten to 4. WARNING Motorcycle operation with insufficient, deteri- orated, or contaminated transmission oil kawazaki accelerated wear and may result in transmission seizure, and injury.

If a reed becomes wavy, replace the valve part with a new one even if its warp is less than the service limit. Cover is in very good condition.

Mating section on the clamp at outside. Jawasaki are subject to change without notice, and may not apply to every country. Special Tool – Outside Circlip Pliers: The picture is of the actual item you will receive. Covers kx and kx I Unit in- spection. KxKxKx Never used, no scratches but may not be quite perfect due to age.


Exhaust Valve Left 34a. Spark plug dirty, damaged, or maladjusted KIPS ports stuck closed Spark plug cap kaqasaki high tension wiring dam- KIPS exhaust valves stuck closed valve aged seizure, or carbon accumulation. Page Remove the clutch see Clutch Removal. Overall Height 1 mm Idle Adjusting Screw B. All microfiche are inserted into new sleeves. Air Cleaner Duct Side A: By pressing ‘print’ button you will print only current page.

Be sure that all parts are put back in the correct sequence, and facing the proper di- rection, and that all circlips and the washers are properly in manuual. Guaranteed by Mon, Jan 7.

Kawasaki KX KX Service Manual – How-To Motorcycle Repair

Increasing the float height lowers the fuel level and decreasing the float height raises the fuel level. Page 92 Service Fuel Level above the bottom edge of the carb. Apply high temperature grease.

Holding the flywheel steady, with the flywheel holder, and tighten the flywheel bolt KX or nut KX Crankshaft bearing worn or damaged Firing incorrect: All 28 pages are complete and free from tears or stains.

Steering Stem Nut Wrench: Remove the drain plug from the bottom of the float bowl, and screw a fuel level gauge [A] into the plug hole. BRAKES Brake Fluid Bleeding the Brake Line The brake fluid has a very low compression coefficient so that almost all the movement of the brake lever or pedal is transmitted directly to the caliper for braking action.


Apply molybdenum disulfide grease O: If it is scratched or damaged, replace the disc.

2004 Kawasaki KX125 (KX125-M2) OEM Parts

So what you see is exactly what you will receive. Page Install the spring guide [A] so that the thinner portion end [B] is down.

Rebound Damping Adjuster Setting Standard: Mikuni Kwaasaki carburetor helps boost mid-range and top-end power. Clamp the air vent hoses with clamps 2. Bearing Remover Shaft, 9: This is in Pre-Owned Condition.

maual Illustrations and photographs in this publication are intended for reference use only and may not depict actual model component parts. If spoke manul is uneven or loose, tighten the spoke nipples evenly. New other see details. Clutch Cable Line up the slots [C] in the clutch lever, knurled locknut, and adjuster, and then free the cable from the clutch lever. If neces- sary, replace them with new one. For parts or not working. Page Swingarm Pivot Shaft Nut: