EN 50083-9 PDF

DIN EN Cable networks for television signals, sound signals and interactive services – Part 9: Interfaces for CATV/SMATV headends. Buy CEI EN CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES – PART 9: INTERFACES FOR . BS EN Cable networks for television signals, sound signals and interactive services – Interfaces for CATV/SMATV headends and similar.

Author: Mazugal Kazrajar
Country: Bangladesh
Language: English (Spanish)
Genre: Finance
Published (Last): 27 January 2010
Pages: 131
PDF File Size: 8.45 Mb
ePub File Size: 4.96 Mb
ISBN: 639-6-24442-570-6
Downloads: 66202
Price: Free* [*Free Regsitration Required]
Uploader: Nishicage

The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS. The variable ACCTn is the accumulator in the loop filter, and it converges to the time interval between arriving sync bytes. A detailed specification of the SSI is provided in annex A and guidelines for its implementation are provided in annex D.

The abstract ASI delivery model is used to make sure that the isochronous output stream from the receiver buffer is similar to the isochronous input stream to the variable delay function.

EVS-EN 50083-9:2002

Data are removed from this buffer at a constant rate, determined by the receiver clock rx-clk. The accuracy of the derived clock is depicted by Amean and Asd for the frequency, and Tmean and Tsd for the time.

As the bytes are removed from the ASI receiver buffer at the average rate, the buffer occasionally fills with excess bytes.

The synchronous serial interface SSI which can be seen as an extension of the parallel interface, is briefly introduced in subclause 4. Safety requirements EN Part 2: Optical measurements shall be made with the cable terminated with the optical connector and the optical fibre specified above.

The first byte received after the second K The parameters shall be met over the temperature, voltage, and lifetime range of the system. The time gate window consists of time slices.

  CCNL CHIMICO FARMACEUTICO 2012 PDF

This is intentional as it leaves maximum implementation flexibility for different 500883-9. While the Fibre-Channel FC supports single mode fibre, multi-mode fibre, coaxial cable and twisted pair media interfaces, this standard defines only two distinct forms 50083–9 interfaces: Because the link and the TS are synchronous, the bit justification operation is not needed. Special characters are defined as extra code points beyond the need to encode a byte of data.

The MPEG-2 Transport Packet synchronization byte 47H is included in this Layer-2 packet definition to allow receive equipment to achieve synchronization. This gives implementers the freedom to deviate from isochronous data delivery.

Note that the interface as such is transparent to the RS bytes. The aperiodicity can be 5008-39 as a short-term change in the transport rate. The interface parameters valid for this network have to be met. The clock frequency fp depends on the transmission rate.

Logic convention The terminal A of the line driver is positive with respect to the em B for a binary 1 and negative for a binary 0 see Figure To restore the original clock rate, a PLL circuit can be used. Need more than one copy? 5008-39 system shall be designed to fulfil the high stability requirements of the modulator clocks, even when several links are cascaded.

Transport packet data word 8 bit: For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. Add to Alert Enn. The Transport Stream is designed for use in environments where errors are likely, such as storage or transmission in lossy or noisy media.

The packet synchronization process is not a part of this ASI Transmission protocol definition.

50083–9 packet timing Transport packets may be presented to Layer-2 either as a burst of contiguous bytes as shown in Figure B. For coaxial cables equivalent to RG 59 BU: The sync byte detector produces a time error between the detected and the hypothesized arrival times. Packet synchronization At least two synchronization code words K In the case of fibre-optic application, the serial bit stream is passed through a driver circuit which drives an optical transmitter LED or LASER which is coupled to a fibre-optic cable through a connector.

  LINGUAGEM JURIDICA E ARGUMENTAO PDF

The ASI specification allows for unlimited time displacement of data bytes.

To maximise equipment interoperability, it is suggested that equipment with an ASI output should be designed to work with equipment with a small ASI receiver buffer. The 10B transmission code is defined in terms of “disparity”, i. The masks allow for HF jitter present in the timing signal associated with the source of interface signal When using an oscilloscope technique to determine pulse compliance with the mask, it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter.

The basic unit of Layer-0 is the link. The frequency accuracy is shown by computing the mean Amean and standard deviation Asd of this inverse. Higher loss fibre may be used for shorter fibre cable lengths.

Distinction between the three transmission formats on the serial link is performed as follows: These normative references are cited at the appropriate places in the text and the publications are listed hereafter. Interfaces pour les tetes de resaux pour antennes communautaires, antennes collectives par satellite et materiels professionnels a.

EVS-EN – Estonian Centre for Standardisation

Another example uses a more well-behaved stream. The serial signal is Biphase Mark encoded. Fibre length shall be sufficient to ensure equilibrium mode distribution.